Production of composite of AISI steel type 1020 and titanium by cladding

Ana Luiza André, Isabella Carolina Conceição, José Carlos de Lacerda, Ricardo Luiz Perez Teixeira

Abstract


The purpose of this work is to describe the research proposal of use of cladding to produce an AISI type 1020 and titanium steel sandwich structure. This work was presented at the VI GPESE Workshop of the Exhaust Systems Research Group of the Federal University of Itajubá. A brief review was used to investigate the main components of the cladding process in the literature to obtain a sandwich-type composite (clad). It is expected that the properties of the sheet steel combined with the titanium powder, generate a material having a long cutting strand where the titanium is placed, and the surfaces both lower and upper, have good impact strength.


Keywords


Cladding. Steel. Titanium. Workshop GPESE.

References


Alam, T., Khan, M. K., Pathak, M., Ravi, K., Singh, R. & Gupta, S. K. (2011). A review on the clad failure studies. Nuclear Engineering and Design, 241(9):3658-3677.

De Almeida, P. S. (2018). Ferramentaria de Corte, Dobra e Repuxo: Fundamentos técnicos, cálculos, máquinas e materiais utilizados. Editora Saraiva.

Escobar, J. D., Poplawsky, J. D., Faria, G. A., Rodriguez, J., Oliveira, J. P., Salvador, C. A. F., ... & Ramirez, A. J. (2018). Compositional analysis on the reverted austenite and tempered martensite in a Ti-stabilized supermartensitic stainless steel: Segregation, partitioning and carbide precipitation. Materials & Design, 140, 95-105.

Froes, F. H. (Ed.). (2015). Titanium: physical metallurgy, processing, and applications. ASM International.

GPESE (2019). Grupo de Pesquisas em Sistemas de Exaustão – GPESE. Disponível em: < https://www.gpese.org/>. Acesso em: 2 julho de 2019.

Helman, H., & Cetlin, P. R. (1993). Fundamentos da conformação mecânica dos metais. Universidade Federal de Minas Gerais, Escola de Engenharia, Fundação Christiano Ottoni.

Melo, E. G., & Xavier, C. R. (2018). Caracterização microestrutural dos aços AISI 1020, 1045 e 4340 após ensaio de temperabilidade Jominy. Cadernos UniFOA, 6(2 Esp), 49.

Semiatin, S. L., & Piehler, H. R. (1979). Formability of sandwich sheet materials in plane strain compression and rolling. Metallurgical Transactions A, 10(1), 97-107.

Takenaka, R. R. M. (2018). Production and characterization of laminated metal composite produced by cold roll bonding. Research, Society and Development, 8(2), 4082749.

Yang, D. H., Luo, Z. A., Xie, G. M., & Misra, R. D. K. (2018). Effect of interfacial compounds on mechanical properties of titanium–steel vacuum roll-cladding plates. Materials Science and Technology, 34(14), 1700-1709.




DOI: http://dx.doi.org/10.33448/rsd-v8i10.1166

Refbacks

  • There are currently no refbacks.


Base de Dados e Indexadores: Base, Diadorim, Sumarios.org, DOI Crossref, Dialnet, Scholar Google, Redib, Doaj, Latindex, Redalyc, Portal de Periódicos CAPES

Research, Society and Development - ISSN 2525-3409

Licença Creative Commons
Este obra está licenciado com uma Licença Creative Commons Atribuição 4.0 Internacional

Rua Irmã Ivone Drumond, 200 - Distrito Industrial II, Itabira - MG, 35903-087 (Brasil) 
E-mail: rsd.articles@gmail.com
Facebook: https://www.facebook.com/Research-Society-and-Development-563420457493356